camaro rear end width

The question is did the track width increase between the 2nd generation and 3rd generation Camaros. This is just the housing only with torque arm bracket spring perches lower control arm brackets rear shock mounts and panhard bar mount.

1969 Chevrolet Camaro Z28 Presented As Lot S213 At Las Vegas Nv Camaro Chevrolet Camaro Chevrolet

Actual wheel track could be as much as 6 to 8depending on drum size.

. If it is the Chevy II rear end its very rare and worth more than a Camaro rear end. Available in 3rd Gen 82-92 width 4th Gen 93-02 width or custom narrowed. I have found a rear axle out of a 2000-2002 Camaro Z28.

Does anyone know the width. It lists a 689 camaro as being 60 hub to hub. Chevy S10 2WD GMC S15 2WD.

The 70 to 81 Camaro rear end is 61 inches. I have a 78 Camaro rear end in the truck theres no E in Camaro BTW. I have searched the threads and came to the conclusion that this rear should measure approx.

Joined Jan 27 2007 26 Posts. 5775 1962-1963 Chevy IINova 82 Dropout nova only 5775 1964-1967 Chevy IINova 82 10 bolt or 12 Bolt. Rearends are built to match the vehicles.

59 rows Rear-end track width measurements of classic American cars. 3 Jul 4 2003. Possibly more in the future if I get hooked.

30 rows Width. Approximate rear end widths measured from backing plate to backing plate. Hello guys I have a 10 bolt rear end out of a 79 camaro that has an open differential and drums.

Its hard to find a reliable source for that info. 4 - 5 for small cars 5 - 6 for intermediate cars 6 -. Or order your axles and narrow the rear end to fit them.

Add Width to compensate for drums as follows. Jump to Latest Follow 1 - 3 of 3 Posts. Itd unbelievable that 75 gear put up with 300hp.

Add Width to. 1968 Camaro rearend width. I have looked at a couple of the camaro websites and didnt see any posts or stickys on the width of the 4th gen F body rears.

Camaro 67-69 Firebird 67-69 Nova 68-71 _____ Below is a break down of the measurements of first and second generation rear ends. Would be better if it had the size of diff as well. I think it would be too wide for most hotrod applications and because the Camaro had a three link coil spring suspension you would have to fabricate mounts.

Its pretty close to the stock track with with the wheels Im using 7 wide 4 backspace. 61 I have also concluded from my research a 70-72 Pontiac Tempest rear should measure 61 as well. Jimmy Clarke Registered.

A common one is the 61 wide 70s vintage CamaroChevelleNova and clones 85 rear end. The Camaro did not have a gov-loc truck only. Bigdav160 Jan 27 2012.

As you can see a second generation rear end is 1 longer 12 on each side. The spring pads on the 64-66 rear ends are different but you can make them work. It is a 342 posi with disc.

I am looking to have a 12-bolt rearend built with new axle tubes ridetech brackets disc brakes etcat this point I need to decide the overall width flange to flange. Its a regular clutch posi. The car will be a driver with some roadcourse at the local goodguys shows and other misc events.

Approximate rear end widths measured from backing plate to backing plate. The width is 625 WMS to WMS. I currently have a 8 ford under my 55 and would like to put this Z28 rear end under my 55 if it isnt too wide.

In Chevelles it has coil springs with lots of extra brackets to cut off and the cast in mounting eyes on top where the upper control arm bushings fit. You will need posi unit axles and brakes to complete this. There is a website in the KB that gives housing widths as well as hub to hub but the way they list the dimensions doesnt inspire alot of confidence.

Only show this user. Discussion Starter 1 Mar 5 2007. The total width of the early rear end is about 60 inches and the later one is about 61 inches.

I have found a 10 bolt out of an 83 camaro that has a factory posi and disc brakes. Currie 9-inch rearends for 1967-1981 CamaroFirebird with mono or multi-leaf rear springs are complete ready to bolt-in assemblies with a choice of gear case axle spline differential type gear ratio and brake option making it easy to customize the package to meet almost any need. The brackets are the same so they will interchange with the right wheel offset.

These dimensions do not include brake drums and are measured from backing plate to backing plate. Chevy Malibu Monte Carlo. Outside width of drum to drum.

Only show this user. 66 to 77 Bronco. In CamarosNovas it has leaf springs but the perches wont work with old truck springs.

Hawks Custom 82-2002 Camaro Firebird 88 Rear End Housing Only. The rear end appears to be a borg warner with a factory limited slip and with disk brakes. 1982-88 camaro rear axle width.

Joined Feb 19 2000. 5425 1983-2004 Chevy S10 2WD GMC S15 2WD 75 76 85 86. The total width of the Chevy II rear end is 58 inches and the total width of a 67 to 69 Camaro rear end is 60 inches.

Photo Sharing On Picyou Camaro Chevy Camaro Zl1 Chevrolet Camaro